Fixing Washington

 Perhaps we need a Disney approach to fixing what is wrong in Washington “It’s kind of fun to do the impossible” Walt Disney  

  If they pass laws against guns then you will either make your supplies at home, salvage or do without. Below 1) All American Anti-disarmament Handbook, it is a ammo, gun, supply system in a book  you can make just about anything you might need in an emergency, gun manufacture, repair and ammo production with out loading equipment, three different powders and primers and much more. 2) below is self explanatory and is a operation manual as well as maintenance manual for the gun.3) Salvaging old used brass and how to bring it into a usable condition. To see military e-manuals and gun e-books click here www.firstpatriotpress.com over 70 to chose from. No waiting, get it now as an E-Book! 

Proof of success

The greatest proof of success is the fact that others have achieved it. Richard W Norman

If they pass laws against guns then you will either make your supplies at home, salvage or do without. You can now have a library of such books that will fit on a CD or flash drive for a small investment. Why not? Below 1) How to peaceful exit a potentially deadly situation as well as gun use. 2)Homemad sheet metal brake. This tool was manly designed as a homemade clip factory but was placed in the book below as a hobby tool for bending metal. 3) below is self explanatory and is a operation manual as well as maintenance manual for the gun To see military e-manuals and gun e-books click below. No waiting, get it now as an E-Book! You can now have a library of such books that will fit on a CD or flash drive for a small investment. Why not? If they pass laws against guns then you will either make your supplies at home or do without.

To see military e-manuals and gun e-books click here www.firstpatriotpress.com. No waiting over 70 to chose from, get it now as an E-Book!

    

Lead home made casting pot Magmaw 6 of 20

This is the 1/8 thick pipe I almost used for the melting pot

Using a chop saw. This is in no way anything but an emergency procedure. Do not try this at home. I have some skill with metal and know when to stop and adjust and proceed. 

Milling parts with machine tools is proffered in any circumstance and a chop saw is not a machine tool. But in a time of a national crises a chop saw could be made to do some fantastic things. A chop saw that does not exist but could be made --would be a base with an adjustable vice that will go up and down and side to side and a stop on the saw for depth. With this in mind such a saw could produce near milled parts that could be finished with a file. The chop saw hand work done was done using very small worn out chop saw blades. In my book I show safer but slower solutions to making a SMG bolt by hand. Given that US manufacturing and production has been moved overseas and even if the vast majority of the public had a machine tool they would not be able to walk up to it and make a part. Do not try this at home it is only an example useful for a time of crises. A spinning chop saw blade is moving need the speed of a bullet and a broken chunk of abrasive blade can maim, blind or kill. 

Laying out metal for top lip. Junk Metal is not junk, a few welds and cuts and you create a part.

I first removed a rectangle of metal so as not to wast the metal or the chop saw blade

   

A hand grinder was used to finish the circles.The parts were laid on a flat surface and spot welded and flipped over as you see here. Note the peace at the bottom is 1/4 inch  thick and the rest of the top is 1/8 thick. I need to tap 2 holes for the drain and wanted the extra strength for the drain valve bracket. To view next post click

A Blog has the ability to up date material and even though time has passed and this is an old post I noticed that a lot of people will only view one page and move on. So it seemed practical to place a photo of the finished product on each post.   

 Richard W Norman         
    If they pass laws against guns then you will either make your supplies at home, salvage or do without. 

American Hamdbook on Guns Ammo and Freedom

What makes a mans Character

"All we are is a result of what we have thought." Buda “as a man thinketh so is he” Jesus Christ the Bible

Making a Difference

The main goal of anyone’s life is to discover your work God has planned for you, dedicate your life to your work, and apply your work to make a difference in the lives of our fellow beings. Richard W Norman

If there was ever a war then you will either make your supplies at home, salvage or do without. Below-- Bomb Shelter and Fall out Shelter All the designs were tested by the government and proved useful 1), 2) and 3) below each are the actual plans for home construction designed during the cold war. Eleven plans to chose from as well as Civil Defense manuals instructing you on how to survive nuclear war. Eleven  shelter plans to chose from  You can have them as e-books now as well as military and gun books over 70 titles to chose from. www.firstpatriotpress.com

Lead home made casting pot Magmaw 5 of 20

Using the short bit first. These holes were 1/4 inch drilled on the back of the plate which will allow me to knock out a fire rod if it ever goes bad. Do not try to drill in two 1/2 inch holes from different directions and hope to align up the holes in the middle it will not happen.

Finding a way to drill holes could be essential for producing any number of products. Long holes are a particular challenge. A good example of a long hole every one is familiar with is a gun barrel. The drill is long and has a continual supply of oil flowing to near the point of the cutting bit which allows the flushing out of the chips behind the smaller drill shaft. This is a relatively simple description but sufficient to understand that the chips if not flushed out would bind the drill shaft and freeze the bit in the middle of the long hole. Even a gofer must take the time to remove the dirt or he would be digging his own tomb. With out such a flushing system then you would need to withdraw the bit and remove the chips. What you will see is a simple system but a little time consuming. The 8 inch holes in the casting pot started with a undersized pilot hole then a larger bit and finally a 1/2 bit about 6 inches long. This was the simple part for the twist in the drill bit removes the chips. A long bit has the same 5 or 6 inches of twist at the front and is then supported by a solid shaft. This shaft leaves the chips trapped and soon the drill bit will come to a complete stop. The process from the photos below is simple. Secure the work piece in a drill press vice and line up the location to be drilled use "C" clamps to secure the drill press vice. Add a few drops of oil to the hole each time before drilling. Drill no more than 1/4 inches in at a time when you are using a very long drill bit, lower the drill table and swing the table to the side and use a mechanics magnet to remove the chips still left in the hole. Swing the table back into position add oil and insert the bit in the hole with the drill off. Raise the table in tell the bit bottoms out in the hole. Secure the table clamping lever behind the drill press table. Look at the measurements by the drill handle and turn on the drill-go down 1/4 inch-- and repeat the process.

This system could be used if you ever had to make a gun barrel. In Drilling the 8 inch fire rod holes  do not get in a hurry. This bit is 1 ft long and proposed some problems in drilling these holes First the location for the holes was noted and marked and second a  center punch was used to mark the location of the hole and then a small bit was used to drill the initial holes. Next a short 1/2 inch drill bit was used to drill a hole as deeply as possible. (The shape of the lip of the metal was a factory flaw) The holes were drilled a little lower so the welding on the top would not propose a problem and reduce the risk of possible burn through. 

   Note the chips in the groves will clog the bit and can bind the metal and drill bit causing problems use the measuring marks on the drill press to calculate the depth of each plunge so that you only go about 1/4 inch and no further than (3/8in is pressing your luck) or you will have problems. The drill press table was then lowered and the table swung aside and the chips were removed with a magnet.

Removing the chips from the hole with an automotive magnet. It took 3hrs and 20 minutes to drill the three 8 inch deep holes but in looking at them as short gun barrels it would have equaled 3 Sub Machine Gun barrels  or one every hour and seven minutes.

Two "C" clamps were used to hold the drill press vice in place and this allowed the table to swing back and realign with the bit and the hole. The process was again repeated with a plunge of the drill bit. You can not rush this --total time 3 hours and 20 minutes. So if you were making a gun barrel that that would be about 1 hour and 6 minutes. A few drops of oil was placed in the hole before the bit was used again. The drill bit was inserted in the hole while it was off so as not to create a larger hole. In reinserting the bit turn the chuck by hand if the bit comes to a stop while lifting the drill press table.To view the next post click 

  Richard W Norman 

A Blog has the ability to up date material and even though time has passed and this is an old post I noticed that a lot of people will only view one page and move on. So it seemed practical to place a photo of the finished product on each post.   

If they pass laws against guns then you will either make your supplies at home, salvage or do without. A lot of gun function problems are because the owner does not know how to take it apart and clean it. Below 1) SKS instruction manual 2) M1 Garand Instruction manual 3) M14 and M14A instruction manual with Bipod instructions. To see military e-manuals and gun e-books click here www.firstpatriotpress.com. No waiting, get it now as an E-Book over 70 to chose from!

     

The Disney Approach in Fixing Washington

 Perhaps we need a Disney approach to fixing what is wrong in Washington “It’s kind of fun to do the impossible” Walt Disney  

If they pass laws against guns then you will either make your supplies at home, salvage or do without. Most gun malfunctions happen because people do not know how to take them apart and clean them. Below 1) SKS instruction manual 2) M1 Garand Instruction manual 3) M14 and M14A instruction manual with Bipod instructions. To see military e-manuals and gun e-books click here www.firstpatriotpress.com. No waiting, get it now as an E-Book over 70 to chose from!